Authorised Vendor Thanos AMC-AASD15A 6axis Servo Motion Controller

[Megahowler]

Mine was doing the same... I rerouted display cables to get them away from the power cables.

Also purchased some much higher quality displayport cables..

Have some copper tape here to shield the power cables eventually.. But everything is working perfectly atm

 

[Tronicgr_6DOF]

Another Dirt Rally 2.0 demo race on DIY 6DOF this time, By Chris:

Build details here:
https://www.xsimulator.net/community/threads/peacemakers-6dof-unicorn-build.12523/

Another update on this amazing DIY 6DOF racing rig, Chris is killing it!!

 

[Tronicgr_6DOF]

Some great truly DIY platforms are coming along... can't wait to see them in action...

View attachment 353106

View attachment 353107

A bit of a progress on the DIY 6DOF from Derek here:

 

[khemyst]

SFX-350 (350mm stroke )

 

[Tronicgr_6DOF]

SFX-350 (350mm stroke )

View attachment 358869View attachment 358870

Good! Now if you modify it for push-pull you could use it to make a nice 6DOF Stewart platform with it!

Is it 1605 leadscrew? If so, you need to use 5mm/rev leadscrew parameter in the AMC-AASD15A controller and 350mm stroke...

 

[khemyst]

Good! Now if you modify it for push-pull you could use it to make a nice 6DOF Stewart platform with it!

Is it 1605 leadscrew? If so, you need to use 5mm/rev leadscrew parameter in the AMC-AASD15A controller and 350mm stroke...

I have both 1605 and 1610 for testing but will save push pull setup for 6dof.

 

[thenic123]

Yes, my actuator numbers are identical to what Thanos posts and recommends in his documentation. I edited my post to reflect this info. Thanks!

#1 - left rear
#2 - left front
#3 - right front
#4 - right rear

I have the Thanos AMC-AASD15A Controller and SFX-100 4 actuators. I have some questions.

1: Should I follow diablo2112's actuator placement number for wiring from the actuators to the servo controllers for my setup?

2: Where to find the specific Thanos controller parameters for programming the servo controllers and explanation of what each parameter does?

That's it for now.

 

[thenic123]

See these two links:
https://simtools.us/licenses/

https://simtools.us/about/

Which version of SimTools do I need and which version is stable? Just for home use.

 

[Tronicgr_6DOF]

I have the Thanos AMC-AASD15A Controller and SFX-100 4 actuators. I have some questions.

1: Should I follow diablo2112's actuator placement number for wiring from the actuators to the servo controllers for my setup?

2: Where to find the specific Thanos controller parameters for programming the servo controllers and explanation of what each parameter does?

That's it for now.

Hi,

1.
See in the manual:
https://github.com/tronicgr/AMC-AAS.../AMC-AASD15A_4DOF+TL-Simtools_manual_v2_3.pdf

2.
You can read the changes log of each firmware to see what all the parameters do, but I also have many videos that explain it as well:
https://github.com/tronicgr/AMC-AASD15A-Firmware

 

[Tronicgr_6DOF]

Which version of SimTools do I need and which version is stable? Just for home use.

The pro version is what you need, if you also want to add extra features.

But why not giving a try to the free FlyPT mover? The latest v2.9.5 version includes SFX100 platform example profiles: https://www.xsimulator.net/community/threads/flypt-mover.13464/

Thanks
Thanos

 

[thenic123]

The pro version is what you need, if you also want to add extra features.

But why not giving a try to the free FlyPT mover? The latest v2.9.5 version includes SFX100 platform example profiles: https://www.xsimulator.net/community/threads/flypt-mover.13464/

View attachment 358980

Thanks
Thanos

Ευχαριστώ πολύ Αθανάσιος

 

[thenic123]

Here's some diagrams for the wiring the SFX-100 controllers of how I'm going about it.

Will the emi filter be enough for the wall mains power or do I have to wrap them in anti-emi tape too?

 

[Insert Coin]

Here's some diagrams for the wiring the SFX-100 controllers of how I'm going about it.

Will the emi filter be enough for the wall mains power or do I have to wrap them in anti-emi tape too?

View attachment 359163
View attachment 359164

Not needed. Most important is to shield the servo power cables (from driver to servo, those four pin cables). Do shield the last 1 meter between connectors and servo too and make sure the shield is connected to ground (the last 1 meter too). See first picture here.

 

[fonsofonso]

Hola, me llamo Fonso.
En primer lugar, discúlpame por mi inglés y si mis preguntas molestan.
Vivo en España y quiero montar un sistema de movimiento en mi simulador.
Hasta ahora he visto el SFX-100
Quería saber cómo mejora el sistema Thanos y si es más fácil de montar para alguien con poca idea.
También estoy interesado en saber qué programas puedo usar para que todo el sistema funcione una vez que esté instalado.
un saludo

 

[Tronicgr_6DOF]

Hola, me llamo Fonso.
En primer lugar, discúlpame por mi inglés y si mis preguntas molestan.
Vivo en España y quiero montar un sistema de movimiento en mi simulador.
Hasta ahora he visto el SFX-100
Quería saber cómo mejora el sistema Thanos y si es más fácil de montar para alguien con poca idea.
También estoy interesado en saber qué programas puedo usar para que todo el sistema funcione una vez que esté instalado.
un saludo

If you don't have experience or patience for the DIY SFX100, you can just get a complete package 4 actuators and AMC controller from PT-ACTUATOR: http://www.pt-actuator.com/a/products/p1/33.html

As far as motion software, there are several supported:
1. Simtools
2. FlyPT mover
3. Sim-motion software (sim-motion)

 

[fonsofonso]

[QUOTE = "Tronicgr_6DOF, publicación: 3141924, miembro: 893238"]
Si no tiene experiencia o paciencia para el DIY SFX100, puede obtener un paquete completo de 4 actuadores y controlador AMC de PT-ACTUATOR: http://www.pt-actuator.com/a/products/p1/33 .html

En cuanto al software de movimiento, hay varios compatibles:
1. Simtools
2. Mover FlyPT
3. SD-motion (sim-departamento)
[/CITAR]
Gracias por tu respuesta
Lo que más me asusta es la parte eléctrica, pero con su placa controladora creo que es más fácil que seguir los pasos del manual sfx-100.
Planeo hacer el sistema yo mismo por razones de precio, además de tener una impresora 3D
Me imagino que tengo que seguir todos los pasos del manual SFX-100, excepto la parte eléctrica del controlador que vende, ¿es cierto lo que digo?

 

[Tronicgr_6DOF]

Gracias por tu respuesta
Lo que más me asusta es la parte eléctrica, pero con su placa controladora creo que es más fácil que seguir los pasos del manual sfx-100.
Planeo hacer el sistema yo mismo por razones de precio, además de tener una impresora 3D
Me imagino que tengo que seguir todos los pasos del manual SFX-100, excepto la parte eléctrica del controlador que vende, ¿es cierto lo que digo?

Sure, for DIY, just follow the guide here: https://opensfx.com/

 

[Lonnie Farrare]

Hello, my questions are if I'm building a SFX system and want to switch to Thanos all that needs to be done is to change the Aurdunio board to a Thanos one and switch software from Sim Hub? Once the Thanos is installed we can explore additional servo configurations ?

 

[Dennis Johnson]

Hello, my questions are if I'm building a SFX system and want to switch to Thanos all that needs to be done is to change the Aurdunio board to a Thanos one and switch software from Sim Hub? Once the Thanos is installed we can explore additional servo configurations ?

That is how I understand it>

 

[fonsofonso]

[QUOTE = "Tronicgr_6DOF, publicación: 3142019, miembro: 893238"]
Claro, para bricolaje, solo siga la guía aquí: https://opensfx.com/
[/CITAR]
Hola
Comenzaré a imprimir la pieza y compraré la placa Thanos AMC-AASD15A
¿Cuánto PLA necesito para todas las piezas que necesito imprimir?
Por otro lado, creo que estoy empezando a entender cómo es el proyecto.
En resumen, una vez que tengo los motores, tengo que ensamblarlos y poner la configuración en cada controlador que viene con el motor, enchufarlo a la placa Thanos AMC-AASD15A y cuando eso está ejecutando simtools y ejecutando el juego, ¿es correcto? ?